Vibration Analysis using Accelerometer ADX345

International Journal of Mechanical Engineering

© 2018 by SSRG - IJME Journal

Volume 5 Issue 3

Year of Publication : 2018

Authors : N.G.Alvi, Dr.S.V.Deshmukh

10.14445/23488360/IJME-V5I3P103

How to Cite?

N.G.Alvi, Dr.S.V.Deshmukh, "Vibration Analysis using Accelerometer ADX345," SSRG International Journal of Mechanical Engineering, vol. 5,  no. 3, pp. 12-16, 2018. Crossref, https://doi.org/10.14445/23488360/IJME-V5I3P103

Abstract:

This novel work is related to the vibrations in the drilling operations, where re-searcher focuses on an approach based on the Taguchi method with grey relational analysis for optimizing the process parameters. Taguchi Method is a statistical approach to optimize the process parameters and improve the quality of components that are manufactured. The objective of this study is to illustrate the procedure adopted in using Taguchi Method in the drilling operation. The parameters which affect the vibration is studies, i.e. Drill Diameter, Speed and Feed Rate, which is related to the performance characteristics.

Keywords:

Taguchi Method, Accelerometer, vibrations, Drill Diameter

References:

[1] "Introduction to fuzzy logic using MATLAB" by S. N. Sivanandam, S. Sumathi and S. N. Deepa.
[2] Panda S.S., Mahapatra S.S. "Online multi-response assessment using Taguchi and artificial neural network" International Journal of Manufacturing Research, Vol. 5(3), pp.305-326. 2010. 11
[3] El-Wardany T.I., Gao D., Elbestawi M.A. "Tool condition monitoring in drilling using vibration signature analysis". International Journal of Machine Tools and Manufacture, Vol. 36(6), pp. 687711. 1996.
[4] Fung C.P., Kang P.C., "Multi-response optimization in friction properties of PBT composites using Taguchi method and principle component analysis." Journal of Material Processing Technology, Vo l. 170, pp. 602610. (, 2005).
[5] Chern G. L. and Liang J. M. "Study on boring and drilling with vibration cutting". International Journal of Machine Tools & Manufacture, Vol. 47, pp.133140. (, 2007).
[6] r. Viraj Bhushan Patil, Dr Eknath Raghunath Deore"Experimentation and t-Test of Viscoelastic Vibration Damping", International Journal of Engineering Trends and Technology (IJETT), V37(1),11-14 July 2016.
[7] Jiang B.C., Tasi S.L., Wang C.C. "Machine vision-based grey relational theory applied to I.C. marking inspection." IEEE Transactions on Semiconductor Manufacturing, Vol. 15 (4), pp. 531539. (, 2002).
[8] Kanai M. and Kanda Y. "Statistical characteristic of drill wear and drill life for standardized performance tests." Annals of CRIP, Vol. 27(1), pp. 61-66. (, 1978).
[9] Yang W.H., Tarng Y.S. "Design optimization of cutting parameters for turning operations based on the Taguchi method". Journal of Material Processing Technology, Vol. 84, pp. 122129. (, 1998).
[10] Hasegawa M., Seireg A. and Lindberg R.A. "Surface roughness model for turning". International Journal of Tribology, pp. 285289. (, 1976).
[11] Bonifacio M. E. R., Dinz A. E. "Correlating tool wear, tool life, surface roughness and tool vibration in the finish is turning with coated carbide tools". Wear, Vol. 173, pp. 137-144. (, 1994).
[12] Azouzi R., Guillot M. "Online optimization of the turning using an inverse process neuro-controller Transactions of ASME", Journal of Manufacturing Science and Engineering, Vol. 120, pp. 101107. (, 1998).